WiFi installation in Canada usually costs about $100 to $450 in labour for a home router or mesh setup, plus $250 to $700 for the mesh kit itself (market estimate). Adding wired access points and new network cable runs moves a whole-home job to roughly $1,300 to $3,150. The ranges below are market estimates in Canadian dollars, not a fixed Pixl price. The size of the home, the number of nodes and whether new cable is needed decide where you land.
PCBy the Pixl Canada install team. Calculated October 27, 2026. 8 min read.
- Labour, hardware and cable ranges in CAD
- Four worked scenarios with totals
- What moves the price up or down
- Ten questions to compare installer quotes
- A basic router or mesh setup is mostly labour: about one to three hours at a market rate of roughly $75 to $150 an hour, with a minimum visit charge.
- The mesh kit or access points are a separate purchase. Mesh is the cheaper route; wired access points cost more but are steadier.
- New Ethernet runs are the biggest jump: a finished-wall drop is about $175 to $400 each in the market.
- Pixl does not run new network cable. It sets up the router, mesh nodes and access points you already own.
You are budgeting a WiFi upgrade, comparing two quotes, or deciding between mesh and wired access points.
You only need to change a password or reconnect a TV. See how to change your WiFi password.
What does WiFi installation labour cost in Canada?
Labour for WiFi work is billed by the hour or as a flat visit price. Market rates for a network technician run about $75 to $150 an hour, and most companies apply a minimum visit charge, so a short job rarely costs less than about $100. The ranges below multiply typical hours by that rate and round.
| Job | Typical time | Labour range |
|---|---|---|
| Place and set up one router | 1 to 1.5 hours | $100 to $220 |
| Mesh system, 2 to 3 nodes | 1.5 to 3 hours | $150 to $450 |
| Large or multi-floor home, 4 or more nodes | 3 to 5 hours | $250 to $750 |
| Add one access point to an existing cable | 0.75 to 1.5 hours | $100 to $250 |
| New Ethernet drop in a finished wall (cabling trade) | 2 to 4 hours | $175 to $400 per drop |
Labour covers placing the equipment, naming the network, pairing nodes, moving your devices over and testing the rooms that matter. It does not cover the equipment.
What does the equipment cost?
Hardware is usually the larger part of a mesh job. Prices vary with the WiFi generation and the brand, so treat these as ranges for planning only. For the generation question, see WiFi 6 vs 6E vs 7.
| Item | Range | Note |
|---|---|---|
| Standalone router | $120 to $350 | Fine for a condo or small home |
| Mesh 2-pack, WiFi 6 class | $250 to $450 | Up to about 2,000 sq ft in typical homes |
| Mesh 3-pack, WiFi 6 class | $350 to $700 | Two floors plus a basement |
| Mesh 3-pack, WiFi 7 class | $700 to $1,800 | Multi-gigabit plans and newer devices |
| Ceiling or wall access point | $150 to $350 each | Needs a network cable, usually PoE |
| 8-port PoE switch | $100 to $300 | Powers wired access points and cameras |
| MoCA adapter pair or powerline kit | $80 to $300 | Uses existing coax or power wiring |
What does the whole job cost? Four scenarios
Totals add the hardware range to the labour range for each scenario. They are calculated with Python from the two tables above and rounded to the nearest $50.
| Scenario | What is in it | Total range |
|---|---|---|
| 2-bed condo | Mesh 2-pack, labour $150 to $300 | $400 to $750 |
| 2,000 sq ft house with basement | Mesh 3-pack, labour $200 to $450 | $550 to $1,150 |
| Large house, wired access points | 3 access points, PoE switch, 3 cable drops, labour $250 to $600 | $1,300 to $3,150 |
| Small shop | 3 access points, switch, business router, 3 drops, labour $400 to $900 | $1,600 to $3,800 |
The gap between the second and third rows is the cabling. Wired access points are steadier, but most of the extra cost is cable and switch rather than WiFi gear: about $625 to $1,500 of the $750 to $2,000 difference. If a cable already reaches the spot, the large-house scenario drops to about $800 to $1,950.
What moves the price up or down?
| Driver | Effect | Why |
|---|---|---|
| Home size and floors | Up | More nodes, more testing time. See how many nodes you need |
| Wall material | Up | Plaster, brick and concrete absorb signal, so nodes sit closer together |
| Existing network cable | Down | A cable to the spot avoids a new drop |
| Number of devices to move | Up | Each camera, TV and speaker must be reconnected |
| ISP modem changes | Up | Bridge mode and double NAT take extra time. See bridge mode |
| Business needs | Up | Guest network, staff network and payment devices on separate networks |
| Travel and minimum charge | Up | Rural and remote visits often carry a travel fee |
How do you compare two WiFi installation quotes?
Two quotes that look $300 apart often include different things. Put these ten questions to each installer and write the answers next to the price.
- Is the equipment included, or do you buy it? Which model and how many units?
- Is cabling in the quote? If yes, how many drops and who does the work?
- Where will each node or access point go, and why those spots?
- How many hours are included, and what happens if the job runs longer?
- Is there a minimum visit or travel charge?
- Which devices will be moved to the new network: TVs, cameras, printers, smart devices?
- Will there be a guest network and, if you need it, a separate network for cameras?
- How is the signal tested in the rooms you use, and are the results shared with you?
- Who owns the admin login, and will you receive it in writing?
- When do you pay, and is the price fixed before the visit?
What does Pixl do, and what does it leave to others?
| Job | Who does it |
|---|---|
| Place and configure a router, mesh nodes or access points you already bought | Pixl |
| Connect TVs, streaming boxes, cameras, doorbells and other smart devices | Pixl |
| Guest network and device separation on your router | Pixl |
| New Ethernet or structured cable inside walls | A cabling contractor, not Pixl |
| Equipment purchase | You, or ask us for the model to buy |
Pixl gives a fixed quote from photos before booking, and you pay after the job. Send a photo of where the modem sits, the floors in the home and the rooms that drop. Prices on this page are market estimates; Pixl’s own quote is the number that applies.
WiFi installation cost: frequently asked questions
How much does WiFi installation cost in Canada?
A market estimate is $100 to $450 for labour on a home router or mesh setup, plus the equipment. A whole-home mesh job typically lands between $400 and $1,150, and wired access points with new cable runs between $1,300 and $3,150.
Is the router or mesh system included in the price?
Usually not. Most installers set up equipment you buy. Always ask whether the quote lists the hardware model and quantity.
How long does a home WiFi installation take?
One to three hours for a router or a two to three node mesh. Large or multi-floor homes can take three to five hours.
Is it cheaper to do it myself?
Setup itself is cheap if you are comfortable with an app. Paying for help makes sense when nodes keep dropping, when cameras go offline or when you need guest and camera networks separated. See mesh WiFi vs extender first.
What does an Ethernet cable run cost?
A market estimate is $175 to $400 for one drop in a finished wall. Pixl does not run new network cable, so this work goes to a cabling contractor.
Do business WiFi installations cost more?
Usually yes, because they need more access points, a switch, separate staff and guest networks and cable runs. See small business WiFi setup.
When do I pay Pixl?
After the job. Pixl gives a fixed quote from photos before booking.
Get a fixed WiFi quote from photos
Send the modem location, the floors and the rooms that drop. You pay after the job.
Access points vs mesh WiFi
Mesh WiFi vs extender
Smart home installation cost
Smart home packages
Full installation price list
eero, Orbi and Deco setup service
How to set up a router
Slow or disconnecting WiFi
How to choose an extender or mesh system
Sources and method. Labour = typical hours × $75 to $150 per hour (market estimate), rounded, with a minimum visit charge. Scenario totals add the equipment range to the labour range and round to the nearest $50, calculated in Python. Example: 3 access points ($450 to $1,050) + switch ($100 to $300) + 3 drops ($525 to $1,200) + labour ($250 to $600) = $1,325 to $3,150. All figures are market estimates, not a fixed Pixl price.
About Pixl Canada. Pixl Canada is an installation company based in Edmonton, Alberta, serving cities across Canada with TV mounting, security cameras, appliance installation and smart home setup. Call or text (587) 899-7495. Open Monday to Saturday 8am to 8pm and Sunday 9am to 7pm.