TV wall mounting · 6 min read · updated oct 2026
How to Mount a TV on a Brick or Concrete Wall
By the Pixl Canada install team
Quick answer
To mount a TV on solid brick or concrete, use a hammer drill with a carbide masonry bit, concrete screws or sleeve anchors rated for the TV’s weight, and clean the holes before you set the anchors. Do not hang a TV from brick veneer, hollow block or mortar joints alone. If you are unsure what is behind the surface, have a professional check first.
Brick or concrete? We bring the right anchors and the drill. Concrete, tile or stone adds $50 and brick adds $80 to the labour rate, and you see the total before you book. See TV mounting prices
On this page
First, find out what kind of wall you have
“Brick wall” can mean four very different things, and the right anchor depends on which one you have. Knock on the wall, check an edge or a switch plate, and look at the thickness at a window or door opening.
| Wall type | How to recognize it | Can it hold a TV? | Typical fastener |
|---|---|---|---|
| Solid poured concrete | Hard and cold, sounds dull, very thick at openings | Yes | Concrete screws or wedge/sleeve anchors |
| Solid brick | Several layers of brick through the wall, mortar joints visible | Yes, in the brick body | Sleeve anchors or concrete screws |
| Concrete block (hollow) | Rectangular blocks with hollow cores, often painted | Only with the right anchor | Toggle or sleeve-style hollow-wall anchors |
| Brick veneer over studs | Brick outside, wood or metal studs inside a wall cavity | Not through the veneer | Mount into studs behind drywall on the inside |
If your wall is brick veneer on the exterior of the house, this does not apply to an interior living-room wall. An interior wall finished in drywall is a stud wall. Our guide on how to mount a TV on the wall covers that case.
Tools and hardware you need
- A hammer drill (a regular drill will struggle and overheat the bit).
- Carbide-tipped masonry bits that match your anchor.
- Concrete screws, such as Tapcon-type screws, or sleeve anchors rated for the load.
- A level, tape measure, pencil and a stud or masonry scanner.
- A vacuum or hole-cleaning brush, and a drill depth stop or tape on the bit.
- Eye protection and a respirator rated for fine dust.
- A helper to lift the TV onto the mount.
Do not rely on the small plastic anchors and lag bolts that come in a mount’s hardware bag. They are meant for wood studs, not masonry.
Drill and fasten in the right place
- Mark the plate position. Hold the wall plate up, level it and mark every hole. Aim for the brick or concrete body, not the mortar joint, and keep holes away from edges and corners.
- Match the bit to the anchor. ITW’s Tapcon catalogue pairs a 3/16″ screw with a 5/32″ bit and a 1/4″ screw with a 3/16″ bit. Always follow the instructions that come with your fasteners.
- Drill deeper than the anchor. The same catalogue says to drill at least 1/4″ deeper than the anchor’s embedment, and standard Tapcon screws need 1″ to 1-3/4″ of embedment. Mark the depth with tape.
- Clean the hole. Vacuum or brush out the dust. Dust left in the hole reduces how well the anchor grips.
- Drive, do not hammer. Set the drill to rotation only, with the hammer function off, when you drive a concrete screw.
- Check the plate. Pull firmly on the plate. If any anchor spins, moves or feels loose, stop and use a new hole.
- Mount the brackets and lift the TV with a helper. Lock it in place and test the lock.
Fastener ratings, bit sizes and embedment differ by product. Treat this as a general guide and follow the anchor maker’s instructions and the mount’s weight rating. See ITW’s Tapcon anchors catalogue for the details on those screws.
Brick or concrete? We bring the right anchors and the drill. Concrete, tile or stone adds $50 and brick adds $80 to the labour rate, and you see the total before you book.
Drilling dust is a health hazard
Drilling concrete or brick releases fine dust that can contain crystalline silica. WorkSafeBC lists drilling concrete or stone among the activities that release it and says to ask whether water or local exhaust ventilation can keep dust from becoming airborne. It also calls respirators and other protective equipment the least effective control, to be used with at least one other. Read the WorkSafeBC silica page.
- Hold a vacuum nozzle next to the bit while you drill.
- Wear a well-fitted respirator and eye protection.
- Keep the room closed off and clean it with a vacuum, not a broom.
Concrete walls in condos
Most condo buildings are concrete, and drilling into the structure is often regulated by the strata or condo corporation. Before you drill, check your bylaws and ask building management. Some concrete floors and ceilings contain tension cables or reinforcement that should never be hit. Walls are usually different, but do not guess. If you are not sure what is inside the concrete, a scanner and a professional are cheaper than a repair.
For metal studs in condos, see mounting a 75 inch TV on metal studs.
What it costs to have it done
At Pixl Canada, mounting on concrete, tile or stone adds $50 to the labour rate, and brick adds $80. That is on top of the city labour rate and the mount. A fixed mount is $70, a tilting mount $80 and a full-motion mount $125, and hiding wires inside the wall is $99.50. You see the full total on the quote form before you book, and you pay after the job. See TV mounting prices by city and our TV mounting page.
Common mistakes on brick and concrete
- Drilling into mortar. Mortar is softer than brick, and the anchor’s grip can loosen over time.
- Using wood-stud hardware. Plastic anchors and lag bolts are not made for masonry.
- Skipping dust cleaning. A dusty hole weakens the anchor.
- Drilling too close to an edge. The brick or concrete can crack.
- Assuming a thick wall is solid. Hollow block needs different anchors.
- Mounting a heavy TV on a mount rated for less. Check the weight rating on the box.
Frequently asked questions
Can you mount a TV on a brick wall?
Yes, if it is solid brick or concrete and you use the right anchors and a hammer drill. Brick veneer and hollow block need different methods.
What anchors do you use for a TV on concrete?
Concrete screws and sleeve anchors are the usual choices. The anchor must match the drill bit, the hole depth and the weight of the TV and mount. Follow the manufacturer’s instructions.
Should I drill into the brick or the mortar?
Drill into the brick whenever you can. Mortar is softer, so an anchor set in it may loosen over time.
Can I use the hardware that came with my TV mount?
Not for masonry. The included lag bolts and plastic anchors are designed for wood studs and are not a reliable choice for brick or concrete.
How much does it cost to have a TV mounted on brick or concrete?
With Pixl Canada, concrete, tile or stone adds $50 and brick adds $80 to the city labour rate. The quote form shows your total before you book.
Can I drill into my condo's concrete wall?
Often only with permission. Check your bylaws and ask building management first, and do not drill into floors or ceilings without confirming what is inside.
This guide is general information. Anchor ratings and building rules vary, so follow the product instructions and local requirements.
Ready to book? Brick or concrete? We bring the right anchors and the drill. Concrete, tile or stone adds $50 and brick adds $80 to the labour rate, and you see the total before you book.
Part of our complete TV wall mounting guide. Written by the Pixl Canada install team: licensed technicians with $5 million liability insurance, installing TVs, security cameras, smart home devices and appliances across Canada.
Related articles